ECCC
ECCC RECOMMENDATIONS - VOLUME 2 Part III [Issue 4]
TERMS AND TERMINOLOGY FOR POST SERVICE EXPOSED CREEP DATA
blank page
AC/MC/97 [Issue 4] 27/7/05
ECCC RECOMMENDATIONS - VOLUME 2 Part III [Issue 4] TERMS AND TERMINOLOGY FOR POST SERVICE EXPOSED CREEP DATA
PREPARED BY ECCC - WG1.1 - PEDS
Dr S Brett Dr S Concari Dr G Fedeli Dr S Fenton Prof Dr E Gariboldi Dr R Hales Dr S R Holdsworth Dr V Kanta Dr Z Kubon Dr-Ing G Merckling Dr D G Robertson Prof R Sandstrom Dr-Ing P Seliger Dr-Ing C Servetto
Innogy, UK (2001- ) CESI, Italy (2001- ) ENEL Produzione, Italy (1997-2001) PowerGen, UK (1997- ) Politecnico di Milano, Italy (1999- ) ETD, UK (2001-04) [Secretary] ALSTOM Power, UK (1997-2001) SKODA, Czech Republic (2001- ) Vitkovice, Czech Republic (2001- ) Istituto Scientifico Breda, Italy (1997- ) [Convenor] ETD (formerly ERA), UK (1997- ) SIMR, Sweden (1999- ) Siempelkamp, Germany (1998- ) Istituto Italiano della Saldatura, Italy (1999- )
EDITED BY: P SELIGER
APPROVED
DATE 31/8/05 On behalf of ECCC
AC/MC/97 [Issue 4] 27/7/05
blank page
AC/MC/97 [Issue 4] 27/7/05
ABSTRACT ECCC Recommendations – Volume 2 Part III presents terms and terminology, with explanations, where required, related to post service exposed materials.
ECCC Recommendations Volume 2 Part III user feedback is encouraged and should be sent to: Dr P Seliger [Document Controller] Siempelkamp Prüf-und Gutachter-Gesellschaft AM Lagerplatz 4 D-01099 Dresden Germany. Tel: +49 351 82 49 320 Fax: +49 351 82 49 329 E-mail:
[email protected]
ECCC may from time to time re-issue this document in response to new developments. The user is advised to consult the Document Controller for confirmation that reference is being made to the latest issue.
This document shall not be published without the written permission of the ECCC Management Committee
AC/MC/97 [Issue 4] 27/7/05
blank page
AC/MC/97 [Issue 4] 27/7/05
Contents of Volume 2 Part III Foreword 0
Identification of Source of Test Results and Material Code
0.1
1
Post Service Exposed (PE-) Material Details
1.1 - 1.5
2
Test Types
2.1 - 2.7
3
Test Details
3.1 - 3.7
4
Standard Terms and Symbols
4.1 - 4.5
5
Data Assessment, Collation and Storage – Definitions of Terms Used
5.1 – 5.6
AC/MC/97 [Issue 4] 27/7/05
blank page
AC/MC/97 [Issue 4] 27/7/05
FOREWORD For “Post exposure data“ it is recognised that additional terms and terminology are required in addition to those in Part I. -
identify details associated with the state and location of sampling of post exposure material, i.e. material sampled from a component after a defined period of service.
-
identify the service details of the sampled material.
-
define the terminology related to the special testing techniques applied to post exposure material testing.
-
define the particular terms used for the creep data assessment of post exposure material.
Section 1 defines the information required to characterise material sampled after service exposure including production details as well as the service conditions. In Section 2 special testing techniques like Small Punch and Indention Creep Testing were added. Section 3 includes test details