E-Book Overview
ESAB AB. Goteborg, Sweden. XA 00150520. 05.2010. 32p. This guide provides practical information on the use of the ESAB all-positional rutile cored wires listed below.
E-Book Content
Welder guide book All-positional rutile flux cored wires for non and low alloyed steels XA 00150520 Contents Introduction 3 Before you start welding 4 Contact tip and gas nozzle 8 Polarity and inductance 10 Welding parameter setting 11 ASME and EN ISO positions 13 Choice of wire size 14 Recommended parameter settings 16 Direction of travel Welding positions Vertical up welding techniques Split-weave and stringer beads Mechanised welding Grinding Trouble shooting 18 19 22 23 24 26 27 Product AWS A5.20 OK Tubrod 15.13 E71T-1C H4 OK Tubrod 15.13S E71T-9 H4 OK Tubrod 15.14 E71T-1C E71T-1M FILARC PZ6113 E71T-1C H4 E71T-1M H8 FILARC PZ6114 E71T-1M H8 E71T-1MJ H4 FILARC PZ6114S E71T-1CJ H4 Dual Shield 7100 Ultra E71T-9C H8 E71T-9M Dual Shield 7100 LH E71T-1C E71T-1M Dual Shield 7100S E71T-1C OK E71T-1 E71T-1C H4 71T E71T-9C H8 E71T-1M H8 AWS A5.29 OK Tubrod 15.17 FILARC PZ6116S E81T1-Ni1M E81T1-K2 J H4 FILARC PZ6138 E81T1-Ni1M JH4 FILARC PZ6138 SR FILARC PZ6138S SR E81T1-Ni1M J E81T1-Ni1C J AWS A5.29 2 Dual Shield 55 E91T1-Ni1M Dual Shield 62 E101T1-G Dual Shield II 81-K2 E81T1-K2 OK Tubrod 15.09 E111T1-K3MJ-H4 Introduction This guide provides practical information on the use of the ESAB all-positional rutile cored wires listed below. When correctly applied, these wires provide: • Excellent weldability with spray arc droplet transfer in all welding positions. • Good weld appearance with smooth weld metal wetting. • High productivity, especially in vertical-up position. • Defect free welds with good mechanical properties. • Low-hydrogen weld metal. EN ISO 17632-A T 42 2 P C 1 H5 Shielding Gas T 46 2 P M 1 H10 T 46 3 P C 2 H5 CO2 Ar / 15-25 CO2 CO2 T 46 2 P C 2 H5 T 46 2 P M 2 H5 CO2 Ar / 15-25 CO2 T 42 2 P C 1 H5 T 46 2 P M 1 H10 CO2 Ar / 15-25 CO2 T 46 4 P M 1 H5 T 46 4 P C 1 H5 Ar / 15-25 CO2 CO2 T 42 3 R C 1 H10 T 42 3 R M 1 H10 CO2 Ar / 15-25 CO2 T 42 2 P C 1 H5 T 46 2 P M 1 H10 CO2 Ar / 15-25 CO2 CO2 T 42 2 P C 1 H5 T 46 2 P M 1 H10 CO2 Ar / 15-25 CO2 CO2 EN ISO 17632-A T 46 3 1Ni P C 2 H5 T 46 4 1Ni P M 2 H5 T 46 6 1.5Ni P C 1 H5 CO2 Ar / 15-25 CO2 CO2 T 50 6 1Ni P M 1 H5 Ar / 15-25 CO2 T 46 6 1Ni P M 1 H5 T 46 6 1Ni P C 1 H5 Ar / 15-25 CO2 CO2 EN ISO 18276-A T 55 4 Z P M 2 H5 T 62 4 Mn1.5Ni P M 2 H5 Ar / 15-25 CO2 Ar / 15-25 CO2 Ar / 15-25 CO2 T 69 4 2NiMo P M 2 H5 Ar / 15-25 CO2 3 Before you start welding In order to fully benefit from the excellent weldability of ESAB all-positional rutile cored wires, the welding equipment needs to be maintained in good condition. The following checklist serves as a guide. CHECKLIST Contact tips and gas nozzle ✓ Remove spatter and replace worn or damaged contact tip. correct ✓ Grind the end of the liner conical for optimal fitting of the contact tip (ESAB M8). Contact tip size, liner size and wire diameter ✓ Ensure that the contact tip is the correct