E-Book Overview
This book covers a wide range of applications and uses of simulation and modeling techniques in polymer injection molding, filling a noticeable gap in the literature of design, manufacturing, and the use of plastics injection molding. The authors help readers solve problems in the advanced control, simulation, monitoring, and optimization of injection molding processes. The book provides a tool for researchers and engineers to calculate the mold filling, optimization of processing control, and quality estimation before prototype molding.Content: Chapter 1 Introduction (pages 1–24): Huamin ZhouChapter 2 Background (pages 25–47): Huamin ZhouChapter 3 Mathematical Models for the Filling and Packing Simulation (pages 49–70): Huamin Zhou, Zixiang Hu and Dequn LiChapter 4 Numerical Implementation for the Filling and Packing Simulation (pages 71–128): Huamin Zhou, Zixiang Hu, Yun Zhang and Dequn LiChapter 5 Cooling Simulation (pages 129–156): Yun Zhang and Huamin ZhouChapter 6 Residual Stress and Warpage Simulation (pages 157–193): Fen Liu, Lin Deng and Huamin ZhouChapter 7 Microstructure and Morphology Simulation (pages 195–236): Huamin Zhou, Fen Liu and Peng ZhaoChapter 8 Development and Application of Simulation Software (pages 237–254): Zhigao Huang, Zixiang Hu and Huamin ZhouChapter 9 Noniterative Optimization Methods (pages 255–282): Peng Zhao, Yuehua Gao, Huamin Zhou and Lih?Sheng TurngChapter 10 Intelligent Optimization Algorithms (pages 283–292): Yuehua Gao, Peng Zhao, Lih?Sheng Turng and Huamin ZhouChapter 11 Optimization Methods Based on Surrogate Models (pages 293–312): Yuehua Gao, Lih?Sheng Turng, Peng Zhao and Huamin ZhouChapter 12 Feedback Control (pages 313–337): Yi Yang and Furong GaoChapter 13 Learning Control (pages 339–353): Yi Yang and Furong GaoChapter 14 Multivariate Statistical Process Control (pages 355–375): Yuan Yao and Furong GaoChapter 15 Direct Quality Control (pages 377–389): Yi Yang and Furong Gao
E-Book Content
COMPUTER MODELING FOR INJECTION MOLDING COMPUTER MODELING FOR INJECTION MOLDING Simulation, Optimization, and Control Edited by HUAMIN ZHOU Huazhong University of Science and Technology Wuhan, Hubei, China A JOHN WILEY & SONS, INC., PUBLICATION Copyright © 2013 by John Wiley & Sons, Inc. All rights reserved. Published by John Wiley & Sons, Inc., Hoboken, New Jersey. Published simultaneously in Canada. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, scanning, or otherwise, except as permitted under Section 107 or 108 of the 1976 United States Copyright Act, without either the prior written permission of the Publisher, or authorization through payment of the appropriate per-copy fee to the Copyright Clearance Center, Inc., 222 Rosewood Drive, Danvers, MA 01923, (978) 750–8400, fax (978) 750–4470, or on the web at www.copyright.com. Requests to the Publisher for permission should be addressed to the Permissions Department, John Wiley & Sons, Inc., 111 River Street, Hoboken, NJ 07030, (201) 748–6011, fax (201) 748–6008, or online at http://www.wiley.com/go/permission. Limit of Liability/Disclaimer of Warranty: While the publisher and author have used their best efforts in preparing this book, they make no representations or warranties with respect to the accuracy or completeness of the contents of this book and specifically disclaim any implied warranties of merchantability or fitness for a particular purpose. No warranty may be created or extended by sales representatives or written sales materials. The advice and strategies contained herein may not be suitable for your situation. You should consult with a professional where appropriate. Neither the publisher nor author shall be liable for